525+530+533 of Xebex International, Ltd.

Brittle Point Temperature Tester
Model No.525 Series
525-FS-Brittlepoint.jpg

Sample of rubber or plastic is immersed in liquid at low temperature, impact is applied by hammer at
constant speed and evaluation is made from generation of cracks.



Model FS
- Testing standard: ASTM D746, ISO-974, JIS K6723/K7216
- Refrigerator type
- Number of samples: 5 samples, 38 x 6.3 x 2mm thick
- Temperature: up to -70゚C
- Power supply: 100V AC, 50/60Hz (supplied with a transformer for local voltage)
- Dimensions & weight: 65(W) x 70(D) x 125(H) cm, Net about 190kg

525-S-Brittlepoint.jpgModel S
- Testing standard: ASTM D746, ISO-974, JIS K6723/K7216
- Dry ice type
- with 2 chucks
- Number of samples: 5 samples, 38 x 6.3 x 2mm thick
- Temperature: up to -70゚C
- Power supply: 100V AC, 50/60Hz (supplied with a transformer for local voltage)
- Dimensions & weight: 58(W) x 71(D) x 47(H) cm, Net about 110kg

LinkIconCatalogue

 
MIT Type Folding Endurance Tester
No.530
530-MIT-DA.jpg

Used for measuring folding endurance of paper, plastic film, leather, flexible printed circuit board, etc.



Model DA (Dead weight type)
- Load : 2.45 to 19.6N or 0.98 to 9.8N (please select one of them.)

Model SA (Spring type)
- Load : 4.9 to 14.7N

<Common Specifications>
- Testing method: ASTM D2176, ISO-5626, JIS P8115, TAPPI T511
- Folding angle: 45, 90 and 135゚ (left/right)
- Revolutions: 90 or 175 cpm (selectable)
- Counter: 6-digit electronic counter
- Power supply: 100V AC, single phase, 3A (supplied with a transformer for local voltage)
- Dimensions & weight: 25(W) x 35(D) x 49(H) cm, Net about 25kg

LinkIconCatalogue

 
Heat Deformation Tester
Model No.533
533 HDT.jpg

Used to evaluate thermal properties of plastics regarding the Deflection temperature under load (DTUL), Vicat softening temperature (VST) and Ball pressure temperature



Model 3M-2
- Testing standards: ISO-75, ISO 306, IEC 335-1, JIS K7191, JIS K7206
- Sample holder: 3 holders
- Test temperature range: Room temp. up to 300゚C
- Test tank: Oil tank (approx. 16L)
- Heating rate: 120゚C/h, 50゚C/h (arbitraty setting by PC)
- Temperature distribution: +/-0.5゚C (near the sample)
- No. of temp. sensor: 4 Pt sensors
- Displacement measurement: Differential transformer, 1/1000mm indication, 0 to +/-2mm
- Stirrer: Parallel ciuculation system (propeller type)
- Cooling system: U-tube type heat exchanger (forced oil circulation, 200W motor)
- Test items: Flatwise test (DTUL), Edgewise test (DTUL/option), Vicat test & Ball pressure test (option)
- Power supply: 100V AC, single phase, 2.7kVA (supplied with a transformer for local voltage)
- Dimensions & weight: 72(W) x 63(D) x 135(H) cm, Net approx. 150kg

Model 6M-2
- Sample holder: 6 holders
- Test tank: Oil tank (approx. 28L)
- No. of temp. sensor: 7 Pt sensors
- Power supply: 100V AC, single phase, 4.5kVA (supplied with a transformer for local voltage)
- Dimensions & weight: 101(W) x 63(D) x 138(H) cm, Net approx. 180kg
- The other specifications are the same as those above.

* Some of Available Accessories in Option:
- Edgewise test (DTUL)
- VICAT test (VST)
- Ball pressure test
- Calibration kit
- Secondary cooling unit


LinkIconCatalogue